Product ID:DERAKANE 411-45,VINYL ESTER RESIN
MSDS Date:01/01/1985
FSC:8030
NIIN:00N001059
MSDS Number: BCGXV

DOW CHEMICAL USA

2020 DOW CENTER
MIDLAND, MI 48640-6030
US

Cage: EO044

DOW CHEMICAL USA

MIDLAND, MI 48640-6030 US

Telephone: 800-258-2436

Cage: EO044

STYRENE, MONOMER (SARA III)

CAS: 100-42-5

RTECS: WL3675000

Fraction By Weight: 50%

OSHA PEL 100 PPM

ACGIH TLV: S,50PPM/100STEL;9293

EPA Report Quantity: 1000 LBS

DOT Report Quantity: 1000 LBS

VINYL ESTER RESIN

Fraction By Weight: 50%

Effects of Overexposure:EYE CONT: IRRIT,TRANSIENT CORNEAL INJURY. SKIN:
RPT/PRLG CONT IRRIT,SUPFIC BURNS. INHALATION: IRRIT

First Aid:EYE: FLUSH WITH WATER 15 MIN,SEE MD. SKIN: FLUSH WITH
WATER,SEE MD. INHALATION: REMOVE TO FRESH AIR,START ARTIF RESP IF
NEEDED,SEE MD. INGESTION: INDUCE VOMITING,SEE MD. (NOTE: NO KNOWN
ANTIDOTE).

Flash Point:90-95F (TOC)
Lower Limits:1.1
Upper Limits:6.1
Extinguishing Media:FOAM,CO2,DRY CHEMICAL
Fire Fighting Procedures:GOGGLES,SELF CONT BREATH APP
Unusual Fire/Explosion Hazard:EXOTHERMIC REACTION UPON EXPOSURE TO HEAT
OR FLAME

Spill Release Procedures:USE APPROPRIATE SAFETY EQUIP. KEEP AWAY FROM
HEAT OR FLAME SOURCE. RESIN CAN BE REMOVED WITH METHYLENE
CHLORIDE,ACETONE,OR AN AROMATIC SOLVENT. (NOTE: THESE HAVE SEPARATE
TOXICITY AND FLAMMABILITY HAZ ARDS).

Handling and Storage Precautions:PRACTICE GOOD CARE AND CAUTION TO
AVOID SKIN AND EYE CONTACT. AVOID BREATH VAPORS. STORE TEMP RANGE
50-80F. KEEP FROM SOURCES OF HEAT
Other Precautions:HAZARDOUS POLYMERIZATION.

Respiratory Protection:NIOSH/MSHA APPROVED RESP DEVICE IN ACCORD WITH
EXPOSURE OF CONCERN
Ventilation:GENERAL/LOCAL AS REQ TO MAINTAIN TLV
Protective Gloves:YES
Eye Protection:CHEM GOGGLES
Other Protective Equipment:CLEAN,BODY-COVERING COVERALLS.
Supplemental Safety and Health

Boiling Pt:B.P. Text:294F
Vapor Pres:7
Vapor Density:3.6
Spec Gravity:1.040
Solubility in Water:INSOLUBLE
Appearance and Odor:STRAW YELLOW VISCOUS LIQUID, PUNGENT STYRENE ODOR
Percent Volatiles by Volume:50

Stability Indicator/Materials to Avoid:YES
OXIDIZING MATERIAL
Stability Condition to Avoid:DIRECT SUNLIGHT,TEMPS ABOVE 120F
Conditions to Avoid Polymerization:OXIDIZING MAT,DIRECT SUNLIGHT OR
TEMPS ABOVE 120F

Waste Disposal Methods:RESIN CAN BE DISPOSED OF THROUGH BURNING IN AN
ADEQUATE INCINERATOR OR BURYING IN AN APPROVED LANDFILL.
LOCAL,STATE AND FEDERAL LAWS APPLY.

Disclaimer (provided with this information by the compiling agencies):
This information is formulated for use by elements of the Department
of Defense. The United States of America in no manner whatsoever,
expressly or implied, warrants this information to be accurate and
disclaims all liability for its use. Any person utilizing this
document should seek competent professional advice to verify and
assume responsibility for the suitability of this information to their
particular situation.